Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Opener Repair for Lubbock Homeowners
A garage door opener that quits leaves your car stuck inside and your Lubbock home open to the alley. Most opener failures come down to a handful of causes: a stripped drive gear, a fried logic board, misaligned safety sensors, or a motor that’s finally worn out after years of daily use. We diagnose the actual fault before we quote you anything, then repair what’s broken instead of pushing a new unit you don’t need. Our technicians have up to 13 years of experience across every major opener brand, and same-day service is often available when you call early. We’re licensed and insured, estimates are free, and the price is agreed before any work starts. Call (866) 361-7024. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Garage Door Opener Installation
Garage Door Opener Installation is the job of fitting a new opener unit to your existing door and rail system, and it’s the right call when your current opener has died or when you’re adding a door that never had one. In Lubbock, this covers everything from a basic chain-drive unit to a belt-drive or smart-enabled system that pairs with your phone. We install across LiftMaster, Chamberlain, Genie, and the other brands we service, matching the drive type to your door’s weight and your ceiling clearance. Typical estimated cost for opener installation in Lubbock runs $250 – $550, and the written estimate sets the final price after we measure your setup.
Matching the Opener to Your Door
A single-car door and a heavy double-car door need different pulling power, and a unit sized wrong will strain from day one. We check the door’s balance and weight before recommending a drive type. That way you’re not paying for capacity you don’t need or fighting an opener that’s undersized.
Wiring and Safety Sensor Setup
New openers need a clean power connection, a properly mounted rail, and safety sensors aligned across the door opening. We set the travel limits and force settings so the door reverses correctly on contact. This is also where we confirm the wall button and any keypad are wired and working before we leave.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Opener Replacement
Garage Door Opener Replacement means pulling out an opener that’s beyond economical repair and putting a fresh unit in its place, reusing the existing rail and mounting where it makes sense. It’s the honest answer when a logic board costs nearly as much as a new unit, or when the motor is drawing too much current and tripping the breaker. We handle this across brands, so whether your old unit is a Craftsman or a Wayne Dalton, we can swap it for something current without changing your whole door setup. Replacement typically falls in the same $250 – $550 estimated range as installation, and the written estimate you get sets the final price.
When Repair Stops Making Sense
If two or three parts are failing at once, or the motor itself is going, repair bills can climb past the cost of a new opener. We lay out both numbers side by side so you decide with the facts. There’s no pressure to replace when a repair will hold.
Keeping Your Remotes and Keypad
Most new openers can be programmed to your existing remotes, or come with fresh ones in the box. We re-pair your wall controls and outside keypad as part of the job. You shouldn’t have to relearn how to open your own garage.
Garage Door Remote Programming
Garage Door Remote Programming is the process of pairing a handheld remote, wall console, or keypad to your opener so it responds only to your signal. You need it when a remote stops working, when you buy a replacement, or when you move into a Lubbock home and want the previous owner’s clicker off your system. We program remotes for LiftMaster, Genie, Chamberlain, and the other major brands, and we clear old codes so a lost remote can’t open your door. This is a quick visit, and it fits inside our standard opener repair range of $120 – $320, with the written estimate setting the final price.
Rolling Codes and Frequency
Modern openers use rolling codes that change with every use, which is why an old remote won’t work on a newer unit even after you replace the battery. We match the remote’s frequency and code type to your opener. Getting that wrong is the usual reason a DIY pairing attempt fails.
Clearing Lost or Stolen Remotes
If a remote goes missing, the safe move is to wipe the opener’s memory and re-pair only the remotes you still have. We do that on-site and confirm each one works before we finish. It takes minutes and closes a real security gap.
Garage Door Opener Battery Replacement
Garage Door Opener Battery Replacement covers the backup battery in openers that keep working during a power outage, plus the coin-cell batteries inside remotes and keypads. In Lubbock, where summer storms can knock out power, a dead backup battery means your door won’t lift when the grid goes down. We test the backup battery, swap it if it won’t hold a charge, and replace remote batteries while we’re there. This kind of work fits inside our $120 – $320 estimated opener repair range, and the written estimate sets the final price.
Backup Batteries in Outage-Ready Openers
Battery-backup openers use a rechargeable pack that ages out after a few years even if it’s rarely used. If your door won’t open during an outage, the pack is the first thing we check. A fresh battery restores that function without touching the rest of the unit.
Remote and Keypad Batteries
A remote that needs several presses or only works up close usually just needs a new battery. We replace it and re-test the range so you’re not guessing. Keypad batteries get the same treatment.
Garage Opener Maintenance
Garage Opener Maintenance is a periodic tune-up of the opener and the door it drives: tightening the chain or belt, checking the drive gear, testing the safety reverse, lubricating moving parts, and confirming the force settings are right. It’s worth doing once a year, or any time the door starts sounding rough, because small issues caught early stay small. We service all the major brands, including Amarr and Raynor door systems paired with their openers, so the whole assembly gets checked together. A maintenance visit fits within our $120 – $320 estimated opener repair range, and the written estimate sets the final price.
What a Tune-Up Covers
We adjust the chain or belt tension, check the drive gear for wear, and test that the door reverses on contact. The door’s springs, rollers, and tracks get a look too, since an opener strains when the door itself is out of balance. You get a clear picture of what’s healthy and what’s wearing.
Why Yearly Checks Pay Off
Most opener failures start as a small noise or a slow spot that’s easy to ignore. Catching a worn gear before it strips saves the cost of a motor. A yearly check keeps the door quiet and the opener out of trouble.
Garage Door Opener Not Working
Garage Door Opener Not Working is the catch-all for any opener that won’t lift, won’t close, or responds unpredictably, and the cause is usually one of a few things: a dead remote battery, misaligned safety sensors, a tripped breaker, a broken spring fooling the opener, or a failed logic board. Before you assume the worst, we run a full diagnostic in your Lubbock home to separate an opener problem from a door problem. That matters, because an opener can’t lift a door with a broken spring, and replacing the opener won’t fix it. Diagnostics and repair fall in our $120 – $320 estimated range, and the written estimate sets the final price.
Diagnosing the Real Fault
We test the power supply, the safety sensor alignment, the wall control, and the door’s balance in sequence. That tells us whether the opener is at fault or the door is fighting it. You get a straight answer before any repair begins.
Opener vs. Door Problems
A door that’s off its track or has a snapped spring will stop any opener dead, and the opener often gets blamed. We check the door mechanics first so you’re not paying to replace a unit that was fine. If the door is the issue, we can handle that too.
Garage Door Motor Replacement
Garage Door Motor Replacement is swapping just the motor unit when the drive system has failed but the rest of the opener is sound, or when the motor is overheating, grinding, or tripping its breaker. It’s a targeted fix that can save you the cost of a full replacement when only the motor is at fault. In Lubbock,we handle motor swaps across the brands we service, including Amarr and Wayne Dalton setups, and we check that the door is balanced first so a new motor isn’t asked to do work the door should be doing itself. Motor work falls within our $120 – $320 estimated opener repair range, and the written estimate sets the final price.
Signs the Motor Is Failing
A motor that hums without lifting, smells hot, or trips the breaker is telling you it’s on the way out. Grinding or a loud clunk when the door starts points to internal wear. Catching it early keeps the repair small.
Motor Swap vs. Full Replacement
If only the motor is gone and the board, sensors, and rail are fine, a motor swap is the cheaper path. When several parts are failing together, a new unit often costs less than the sum of repairs. We price both so you can compare.
Brands We Service
We work across the full range of residential opener and door brands, which means your recommendation is based on the system you already own, not on a single product line. We’re certified to service eight major brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. With LiftMaster and Chamberlain, we know the logic boards and MyQ-style connectivity that trip up generic handymen, and we know where their drive gears wear on high-cycle doors. Genie and Craftsman units have their own remote frequencies and sensor quirks, and we’ve diagnosed enough of them to skip the guesswork.
On the door side, Clopay, Amarr, Wayne Dalton, and Raynor panels and hardware work as a system with the opener, so we service both together rather than handing you off between contractors. Whether you have Craftsman, Raynor, or any other make, we can help. That brand-agnostic approach is the point: repair first, replace only when it makes sense.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The door won’t reverse on contact. If the safety reverse fails, the door can close on a child or pet. That’s a stop-using-it-now problem, not a wait-and-see one. We test and fix the sensor and force settings.
- The opener hums but the door doesn’t move. This usually means a stripped drive gear or a broken spring the opener is straining against. Running it longer can burn out the motor. Shut it off and call.
- Grinding or banging when the door starts. Metal-on-metal noise points to worn gears or a door that’s jumped its track. Left alone, it turns a small repair into a motor replacement. It’s worth a look before it gets worse.
- The door opens or closes on its own. Random movement often means a stuck wall button, a bad logic board, or a neighbor’s remote on your frequency. It’s a real security issue. We track the signal and stop it.
- Lights flash and the door won’t close. Flashing lights are the opener telling you the safety sensors are blocked or misaligned. A quick realignment usually solves it, but it needs the right tools to set correctly. Don’t force the door.
Our Process, Step by Step
- 1
You call, we book. Tell us what the door is doing and which brand opener you have, and we’ll set a time that works. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Same-day service is often available.
- 2
On-site diagnosis. We test power, sensors, wall controls, the door’s balance, and the opener’s internal parts in order. That sequence finds whether the opener or the door is the real problem. You watch us work through it.
- 3
A written estimate before work. We lay out what’s wrong, what it costs, and what we’d do, then you approve before we touch a thing. No surprise invoice, no upsell on parts you don’t need. If a repair beats a replacement, we say so.
- 4
The repair. We fix the actual fault, whether that’s a logic board, a drive gear, a sensor set, or a motor. Every adjustment is tested in both directions before we call it done.
- 5
Final check and walkthrough. We confirm the safety reverse works, the remotes pair, and the door runs smooth. You get a plain explanation of what we did and what to watch for.
How Much Does Garage Door Opener Repair Cost in Lubbock?
Garage door opener repair in Lubbock typically runs $120 – $320, and the final price depends on the part that failed and how far the opener has to come apart to reach it. A sensor realignment or remote reprogramming sits at the low end. A logic board or drive gear swap lands higher, and a motor replacement sits near the top of that range. Opener installation and replacement, a bigger job, typically runs $250 – $550. A typical sensor fix in Lubbock runs $120 – $200 depending on the sensor type, while a logic board replacement runs $180 – $320 depending on the board and brand.
What moves the price is mostly the part cost and the brand – some LiftMaster and Genie boards cost more than a Craftsman or Chamberlain equivalent. Accessibility matters too: a low-clearance ceiling or a tight side mount adds time. How to avoid overpaying: get the written estimate first, ask whether the door’s balance was checked, and confirm whether the quote is for repair or replacement. What’s included in a free estimate: a full diagnostic, an explanation of the fault, and a written price for the fix. The written estimate sets the final price, so nothing changes once we’re under the hood. Call (866) 361-7024 for an exact quote – estimates are free.
Our Service Area Near Lubbock
We bring Dunmore Garage Door Repair to homeowners across Lubbock and the surrounding communities, including Wolfforth, Shallowater, Slaton, Abernathy, Ransom Canyon, Idalou, Buffalo Springs, New Deal, and Smyer. Same-day dispatch is often possible on opener problems, especially for calls placed early in the day. If you’re just outside one of these towns, call and we’ll confirm coverage. Our garage door opener repair and garage door opener repair pages cover the outlying areas, and the main garage door opener repair hub has everything else.
Serving Lubbock, TX – Our Local Coverage Area
We serve Lubbock and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Opener Repair in Lubbock
Garage door opener repair is fixing the motor, logic board, drive gear, sensors, remotes, or wiring that make your opener work, without replacing the whole unit. It’s different from installation, which fits a new opener, and from door repair, which fixes the door itself. We diagnose which part is at fault so you pay for the right fix. Call (866) 361-7024 for an exact quote – estimates are free.
Most opener repairs take one to two hours once we’re on-site, though a logic board or motor swap can run a bit longer. Sensor and remote issues are often fixed in under an hour. We give you a time range when we book, and we don’t leave until the door runs right. Call (866) 361-7024 to schedule.
Typical estimated cost runs $120 – $320 depending on the part and brand, with the written estimate setting the final price. Installation or replacement runs $250 – $550. We quote before any work starts, so you approve the number first. Call (866) 361-7024 for an exact quote – estimates are free.
Yes. We’re certified to service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That means we work on your brand, not just one product line. If your opener is a make not on that list, call and we’ll tell you straight whether we can help.
Same-day service is often available when you call early, and we’re closed Saturday. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (866) 361-7024.
Ask about warranty coverage on the specific repair when we quote – it can vary by part and brand, and we’ll tell you exactly what applies before we start. We stand behind the work we do and put the terms in writing. No surprises after the invoice. Call (866) 361-7024 with any questions.
Clear the floor under and around the door, and know where the opener’s power switch or breaker is. If you have the opener manual or model number, have it handy – it speeds up diagnosis on Genie, LiftMaster, and other brands. Tell us what the door is doing when you call, and we’ll come ready.
Schedule Your Garage Door Opener Repair Service in Lubbock Today
A garage door that won’t open is a problem worth fixing today, and we can often do it. Call (866) 361-7024 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We diagnose the real fault, quote before we start, and fix what’s broken – not what isn’t.
Written by the team at Dunmore Garage Door Repair.